You are here : Homee > WELDING

Pack 40 rod + Stainless steel brush offered

75.05 € 79.00 €

Stock : 94

ALL our Rods packs are sold for your personal use
In no case they can beings offered for resale in any


BRUSH  INOX  FREE


Exclusive dealer Durafix EASYWELD in the following countries:
France, Spain, Germany, Switzerland, Austria, Algeria, Morocco and Tunisia 

Now you can repair aluminum and zinc based parts with out a welding machine : 
· All you need is a hand held propane type torch for small pieces. 

· Produces a sound joint that is stronger than the parent metal. 

· No fluxes are required. 

· There are no fumes. 

· Low 732°F. working temperature.

· Joins thin or thick parts

Try the difference between hts-2000, Alumaweld, Alumarod, Alumaloy, A-LUM-RITE by Divesco, Aladdin 3 in 1 or hts2000 : 
Durafix EASYWELD is the best !

Use DURA-FIX For : INDUSTRIAL MAINTAINANCE - FABRICATE REPAIR - FARICATION MAINTAIN - ALUMINUM AND ALLOY
BOAT OWNERS / ARTISTS / HOBBYISTS / RADIATOR SHOPS / VOCATIONAL SCHOOLS /RACE CAR MECHANICS / LOCKSMITHS / GO-CART RACERS / CAMPING ENTHUSIASTS / PLUMBERS / WELDERS / FARMERS / FISHERMEN / HUNTERS / GUNSMITHS / AVIATORS / SPORTSMEN / MACHINISTS / AIR CONDITIONER REPAIRMEN / LAWNMOWER REPAIR SHOPS / TRANSMISSION REPAIRMEN / MOTORCYCLE REPAIRMEN / AUTO-BODY REPAIRMEN / MAINTENENCE MECHANICS / STORM WINDOW FABRICATORS / SOLAR ENERGY FARICATORS / ANTIQUE CAR RESTORATION / And many more... 

FEATURES :
· LOW COST 

· STRONGER THAN ALUMINUM 

· NO FLUXES OR FUMES 

· LOW WORKING TEMPERATURE

Aluminum Welding Instructions :
If you have any problems with Durafix EASYWELD or any questions, do not hesitate to contact us. We will give you personal instructions on how to use our product. Customers that call us with problems leave very satisfied and usually order again.
Clean area to be welded down to base. Brush the base with stainless steel brush till shiny. Heat the area to be welded, evenly. As you heat the base, rub the rod vigorously against the heated piece to be welded till rod flows. Never apply heat directly to rod.
security :
ALWAYS WEAR SAFETY GLASSES AND GLOVES !
Do not use on magnesium. 
If you are unsure of the the material, file off some metal and apply the torch. Magnesium will burn white like a flare.
Will not be held liable for any damages, injury or losses due to the misapplication of this product or any other reason whatsoever 
Download Technical specifications :
Product Description
Technical details
Technical details 2

Specifications : 
Tensile Strength,lbs/sq. in. : 
Compression Strength,lbs/sq. in. : 
Shear Strength,lbs/sq. in. : 
Charpy Impact Str,lbs/sq. in. : 
Hardness (Brinell) : 
Ductility Good : 
Melting Point : 
Specific Gravity : 
Density (Ibs/cu. in.) : 
Elongation (in 2") : 
Coefficient of Linear Expansion : 
Electrical Conductivity : 
Thermal Conductivity : 
Dimensions : 47,000 
60,000 - 75,000 
34,000 
4 ft/lb to break 1/4" bar 
100 
Good 
732°F/390°C 
6.7 
0.25 
3% 
15.4x10-6/°F
24.9% du Cu 
0.24 cal/cu. cm/°C
L : 45cm / Ø 3.2mm
Dura-FIX Rod 
The most widely used rod on the market for WELDING ZINC BASE metals - white - die cast - pot metal. Alloyed from pure virgin metals. Welds made with ROD are clean and free from slag. Produces a sound joint that is stronger than the parent metal. BRAZING ALUMINUM without the use of flux, sound and free from porosity. SOLDERS GALVANIZED, also used as a RUB-ON solder. Use a slightly carburizing flame (excess of acetylene), with small tip for most work. MELTING POINT 732°F. Dura-Fix Is Used TO: Repair Kirksite dies, power tools, aluminum radiators, power mower castings, propellers, lower units and boat hulls. THOUSANDS OF OTHER USES.

General Notes
This rod will work with propane, mapp, butane, oxyacetylene or any fuel source as long as the material is brought up to 732°F. The rod will not work if heated directly. You must heat the material that you are working on to 732°F and then apply the rod. The material must be cleaned with a stainless steel brush (included) because the rod will not adhere to stainless steel. The rod will not adhere to the material being brazed if it is cleaned with a steel or other type brush.